So.. what are you reloading at the moment??

[clelaj]

38 spl, 158 swc, Bullseye. Because I can.

 

[cjcycles]

A few 40 major rounds for USPSA. This is good weather for reloading.

Sent from my iPhone using Tapatalk

 

[IN71vet]

This week I loaded 200 44 SPL 240 gr RNL 7.2 gr HS-6.

 

[sugarcreekbrass]

Just got more 9mm bullets yesterday so hopefully I get them loaded this weekend.

 

[sugarcreekbrass]

I did 1000 9mm this weekend. 124 gr Berry's RN over 4.2 gr of TiteGroup.

 

[cmann250]

I’m just tumbling brass.

124 gr Berry's RN over 4.2 gr of TiteGroup.

What’s the velocity on those? I’m curious about TG for 9 since it seems to be my go to for about everything else.



Sent from my iPhone using Tapatalk

 

[sugarcreekbrass]

I’m just tumbling brass.



What’s the velocity on those? I’m curious about TG for 9 since it seems to be my go to for about everything else.



Sent from my iPhone using Tapatalk

I'm getting around 1080fps. They are 1.150" with CCI SPP.

 

[jeromy0408]

I'm reloading .308 for my remington 700 varmint.

 

[d.kaufman]

Had worked up a few batches of 6.5 creedmoor to try out. Everything from 90gr up to 143gr. The TC compass really liked 2 loads I made.

Top pic is 123gr Hornady Eld match using 40gr Blc-2, Federal gold Medal match primers, with a oal 2.670

Bottom pic is Hornady 140gr Bthp using 34gr Shooters world match powder, Federal Gold Medal match primers and a OAL of 2.80.

Going to see how these loads work with fire formed brass next. Only neck sizing. The groups pictured I was using once fired cases I bought at gun show and full length sized and trimmed to 1.915

Both are 5 shot groups at 100 yards

Not to shabby for a $250 rifle

 

[red_zr24x4]

Those are some nice groups

 

[d.kaufman]

Those are some nice groups

Yeah. I was pleasantly surprised. The rifle definitely liked the mid and heavy bullets. I also tried 90, 95, and 100gr too, since I run those in my grendel. Those grouped between 1.25 and 1.75" May try tweaking those loads a bit and see if I can get them sub moa or not

 

[thecapn2004]

Working on cutting down some .223/5.56 for 300 Blackout reloading. First time doing this so it should be an adventure.

 

[Chalky]

Finished up some 22 hornet. 38 and 357 up next.

 

[tv1217]

Waiting for payday Monday so I can order dies, shell holder, and brass for .50AE

 

[2in1evtime]

Changing powder on my 357 mag loads loaded 100 in different powder and bullet configurations, will try them out tomorrow

 

[cmann250]

Changing powder on my 357 mag loads loaded 100 in different powder and bullet configurations, will try them out tomorrow

I just did that with 38 Special. 2 different bullet weights, 4 different powders, and several different charges of each powder.

All just to settle on a proven HP-38 and 158gr load which is what I’m loading now.


Sent from my iPhone using Tapatalk

 

[led4thehed2]

I've been working up various loads for my M1903. Last week I tried IMR 4064, Varget, BL-C(2) and IMR 4895.

IMR 4064 grouped the best, and IMR 4895 barely hit the paper! The other two were okay, but not as consistent as 4064.

For my next trip I have 3 different powder charges (46.1, 46.6, and 47.4 grains) , 2 kinds of bullets (Hornady 150 FMJ vs generic 147 gr FMJ) and crimped vs. uncrimped rounds. Curious to see to what extent these variables affect accuracy.

 

[tv1217]

Churned out a few .50AE today. 300 Speer Deep Curl over 32 gr of H110. Gonna try to get up to Point Blank after I get off work to see how they do(and finish off my factory stuff)

 

[red_zr24x4]

Set the 550 back up for 9mm. Don't really need any more, but ya know how it is

 

[JStang314]

Trying to run a decent amount of 223. Broke 2 decapping pins. I think I threw the same piece of brass back in the bucket. Seems to be a piece of PMC brass with a very off center flash hole. If it was the same piece of brass, the second one is definitely my fault lol.