List Your 10mm

[dennadam]

Jump on that!
Tanfaglio makes a decent firearm, and $225 is a steal!

I agree, going tomorrow and get it. I'll post pic later this week.

 

[armalitesheepdog]

A shop near my has a EAA Witness in 10mm for $225.00. the gun look to be in good shape, no frame cracks. maybe a good gun to see what I think of 10mm. only use for paper.

​

Sounds to cheap...are you sure 225?

 

[dennadam]

Sounds to cheap...are you sure 225?

yes, hopes it still there tomorrow. that did seem like a low price. I'll really check it over before I buy it.

 

[Mgderf]

It's been years ago now, but I picked up an EAA Witness in the infamous "Wonder Finish" and chambered in .45acp at an estate auction.

The auctioneers had it listed as a "Tanfaglio" and I don't think most who attended the auction knew what they were looking at.

It was in the factory case and had one mag with it but looked like it had never been fired.

A handful of people bid, but only two of us went above $150 before everyone else dropped out.
I brought home what appears to be a brand new Witness for $195 and no transfer fee.
Still have it too, although I don't spend enough time with it.

 

[Colt556]

Colt Delta Gold Cup
Glock 40 MOS with Trigicon RD
Glock 20
Witness Full Size
Witness Compact
S&W 610 5”

Have had other Colts, Glocks and a Ruger Buckeye Convertible 10mm- 38/40 but let them slip away. I really want an AR15 Carbine in 10mm that I don’t have to build or cost $1600 like the CMMG. Just missed another 610 the other day.

 

[dennadam]

It's been years ago now, but I picked up an EAA Witness in the infamous "Wonder Finish" and chambered in .45acp at an estate auction.

The auctioneers had it listed as a "Tanfaglio" and I don't think most who attended the auction knew what they were looking at.

It was in the factory case and had one mag with it but looked like it had never been fired.

A handful of people bid, but only two of us went above $150 before everyone else dropped out.
I brought home what appears to be a brand new Witness for $195 and no transfer fee.
Still have it too, although I don't spend enough time with it.

that's what I like to find, deals. this looks a little used but not bad. not every one like shooting 10mm , I'll find out if I do.

 

[dennadam]

Colt Delta Gold Cup
Glock 40 MOS with Trigicon RD
Glock 20
Witness Full Size
Witness Compact
S&W 610 5”

Have had other Colts, Glocks and a Ruger Buckeye Convertible 10mm- 38/40 but let them slip away. I really want an AR15 Carbine in 10mm that I don’t have to build or cost $1600 like the CMMG. Just missed another 610 the other day.

yeah I got rid of some l like to have back

 

[DadSmith]

https://www.indianagunowners.com/threads/rock-island-ultra-fs-10mm.501306/

Here's my answer. I'll post more when I get more rounds through it.

 

[d.kaufman]

I have a G20 and a RIA and they both shoot very well. Both purchased used so round count unknown but I've put several hundred thru each. Both equally accurate and reliable.

 

[knot4reel]

I own this Ruger SR 1911 in 10mm.
Never had a problem. Its been thru a Ton of my Norma like reloads and showing no signs of wear. I paid $799 about 5 years ago. I don't see them available much any more. If you can find one I would recommend it.
BTW it's one of the more accurate pistols I own

Where did you find this picture of my gun? It's my favorite 1911.

 

[yetti462]

S&W 610 has yet been mentioned. Its a fine piece.

If you are looking at mag fed, then g20/40. Got both and they are fine operating pieces. I too have a sprinfield ronin. No jam issues with it and ahoots great.

So I recommend getting one of each.

 

[dennadam]

I have a Glock 40, recoil is almost non-existent due to its size. However, that is a drawback as its a large pistol.

Enjoy shooting it even with heavier loads, and with a good holster it isnt too bad to carry owb.

I know Glocks are good gun. but don't like the feel in my hand.

 

[dennadam]

S&W 610 has yet been mentioned. Its a fine piece.

If you are looking at mag fed, then g20/40. Got both and they are fine operating pieces. I too have a sprinfield ronin. No jam issues with it and ahoots great.

So I recommend getting one of each.

 

[dennadam]

I had a springfield 1911A1 in 45, nice gun. traded it for a rifle.

 

[dennadam]

S&W 610 has yet been mentioned. Its a fine piece.

If you are looking at mag fed, then g20/40. Got both and they are fine operating pieces. I too have a sprinfield ronin. No jam issues with it and ahoots great.

So I recommend getting one of each.

I'll check one out.

 

[dennadam]

I own this Ruger SR 1911 in 10mm.
Never had a problem. Its been thru a Ton of my Norma like reloads and showing no signs of wear. I paid $799 about 5 years ago. I don't see them available much any more. If you can find one I would recommend it.
BTW it's one of the more accurate pistols I own

that's a good looking gun. I bet it cost a little more now.

 

[2in1evtime]

My Les Bauer Hunter model,[ 6" barrel. Shoots anything i feed it, very accurate and actually pretty soft shooter with max loads, have a 45 also, after the 10 mm i added a 38 super to the mix

 

[mmpsteve]

Colt Delta Elite.

Pro:
It’s a 1911 - Everything runs better in a 1911 platform

Con:
I’ll let you know if I find one

Geez. Nice gun like that, seems like you could slap a modern pair of grips on it!

Just kidding of course. Are those the woolly mammoth grips?

Looks great.

.

 

[dennadam]

My Les Bauer Hunter model,[ 6" barrel. Shoots anything i feed it, very accurate and actually pretty soft shooter with max loads, have a 45 also, after the 10 mm i added a 38 super to the mix

Les Bauer a custom model? 1st I heard that name.

 

[Colt556]

Les Bauer a custom model? 1st I heard that name.

Six post so far in this thread. You’ll have 50 before you know it.